Previous video in the series: https://www.youtube.com/watch?v=xdubsr2dSNg
It became clear after talking with the engineers at Maximum Motorsports that my rear suspension wasn’t going to hold up to the power I was putting to it. That ended up being a very expensive conversation, but it also means that the #FairmontProject will have a very capable suspension when I’m done with it.
I’ve been learning a lot about Fox bodies during the course of this build. One of the things I learned is that the suspension components from Maximum Motorsports are great. I’m not saying this because they paid me to. I’m saying it because I believe it to be true. After all, building Mustang suspensions is ALL they do. You’d think they’d be good at it by now.
Special thanks to Jack Hindley and Kolton Sinclaire for all their help.
Link to MM Rear Control Arms: http://www.maximummotorsports.com/Sport-series-Adjustable-Mustang-Rear-Lower-Control-Arms-1979-1998-P1492.aspx
Installation instructions: http://www.maximummotorsports.com/assets/install/pdf/rear_susp/MMRLCA-102.pdf
Maximum Motorsports website: http://www.maximummotorsports.com/Default.aspx
The #FairmontProject playlist: https://www.youtube.com/watch?v=L22GsHQi7tU&list=PLSzhQ6St-ov2nxWVKCeU14Vt7JJ_QSZvs
The best place for answers to your automotive questions: http://www.ericthecarguy.com
Check out the ETCG Blog for the latest info: https://www.ericthecarguy.com/blog
Camera: Brian Kast
Thanks for watching!
Discussion about this video: https://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/67926-rear-control-arm-installation-fairmontproject
Tools
Torque wrench: http://www.rakuten.com/prod/282405511.html
Related Videos
How To R&R a Fox Body Fuel Tank: https://www.youtube.com/watch?v=TY-Ad71bQu4
Installing the New Differential #FairmontProject: https://www.youtube.com/watch?v=3E9BA6YlhjU
Parking Brake Cable Modification #FairmontProject: https://www.youtube.com/watch?v=YeyaFW1CFPY
Removing the old engine from the Mustang: https://www.youtube.com/watch?v=5wINaHUrX7o&t=905s
Replacing the K Member #FairmontProject: https://www.youtube.com/watch?v=ezbTvonGpi8&t=790s
Installing the Front Stabilizer Bar: https://www.youtube.com/watch?v=9okDlsmIfWQ
Relocating the Battery #FairmontProject: https://www.youtube.com/watch?v=IF8cHIjmUY8
#DarkMatterPikachu on the Dyno: https://www.youtube.com/watch?v=UADOHm6-BJc
Engine Balancing Video: https://www.youtube.com/watch?v=XjuGkXpha8Q
**Answers to your automotive questions found here: http://www.ericthecarguy.com/faq
Social Network Links
Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts
Twitter: https://twitter.com/EricTheCarGuy
Google+: https://plus.google.com/100195180196698058780/posts
Instagram: http://instagram.com/ericthecarguy
Wanna see more stuff like this from ETCG? Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
What tires are you using on the fairmont?
Great Vid! Typical Fox BS. Been there done that… 😃
this just convinced me to get adjustable vs non adjustable, Thanks Eric…..
Next time working on the driver side raise the passenger side rear end on one side will make life easier and Prybar.. didn’t this easy on the floor lol
Should have disconnected the front of the torque arm and used that as leverage to move the axle into place to get that lower control arm bolt in.
love this guy
Just. Thank you.
I went with team z
I feel your pain on getting those lower fasteners through the holes. Major pain in the ass. Especially once the Panhard Bar is installed. The diff won’t want to budge at all. I’ve been there eric.
Just looked at your subscribers, I had no idea you are this close to 1 million. I remember watching at 10k lol
when go to align it, make sure you add weights to the drivers side equal to your weight. this way you will track straight at the strip. Guess you know this already.
Torquing on the ground doesn't matter for a polyurethane bush.
A metalastic bush with rubber bonded to the metal will be in torsion as the control arm pivots and therefore needs to be torqued in the resting position, but a poly bush just rotates.
Washing machine 🐵
People don't like fairmonts! Why don't you understand that!
Eric….I think to make up the money lost for some viewers not watching or enjoying the fairmont series as much as repair videos….you need to race to make some money hahaha jk
I saw a YouTube on those arms by maximum motor sport they have other arms without the swaybar mounts and ones rated for six hundred plus hp those ones look to be the four hundred plus arms, you might want to swap them for the higher rated ones.
Is there a way to lock those spring perches?
Did MM recommend to remove the upper control arms?
Eric, diid you forget to wobble it after the swap? Also – did you consider using scales to weigh your Oliver when adjusting springs?
You keep dropping deez nutz bro,lol
Erick and steady hand Brian, did a fine job. It was amusing my thoughts when you were shaking Peak-a-chu to put music to that clanking noise. You guys rock. Stay Dirty !!.