Custom LED Light Bar Build (Part 2 “Project Night Light”)

Join me in building a custom LED light bar mount for my truck. I start with a drawing and some pieces of metal and make it into a fully functional rig to hold my 42in LED Light Bar. The rack consists of bed rails, a headache rack, and a roof rack, all-in-one, to hold the light bar. I use 1.5in .083 wall square tubing, a 90amp harbor freight flux welder, a grinder, and a cutoff wheel to get the job done.

Episode 1:https://youtu.be/qp9L00SMSHQ?list=PLvKbarVtwhUvttF8SaaIrpSYX4walXQCb
Episode 3: How to Wire an LED Light Bar Properly:

Here is where I got the 42in Wurton lightbar: http://amzn.to/29OF8s0
Welder I used to make my rig: https://amzn.to/2vpDKc6
Grinder I used: http://amzn.to/29OEHOG
Cutoff Wheel I used: http://amzn.to/29VPFRH
Herculiner Paint: http://amzn.to/2ag9z8J
Tap and Die Set I used to thread the bolt into the metal: http://amzn.to/29IUtsJ

Become a ChrisFix Subscriber→ http://www.youtube.com/subscription_center?add_user=paintballoo7
Instagram→ https://www.instagram.com/chrisfixit
Facebook→ https://www.facebook.com/chrisfix8
Website → http://www.ChrisFixed.com
My Channel Home Page → https://www.youtube.com/ChrisFix

**If the video was helpful, remember to give it a “thumbs up” and consider subscribing. New videos every Thursday**

Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

source

Author: avnblogfeed

ANGELHOUSE © 2009 - 2022 | HOSTING BY PHILLYFINEST369 SERVER STATS| & THE IDIOTS ROBOT AND CONTROL INC. |(RSS FEED MODULE)| ALL YOUTUBE VIDEOS IS A REGISTERED TRADEMARK OF GOOGLE INC. THE YOUTUBE CHANNELS AND BLOG FEEDS IS MANAGED BY THERE RIGHTFUL OWNERS (AVNBLOGFEED.COM)

22 thoughts on “Custom LED Light Bar Build (Part 2 “Project Night Light”)

  1. Great design! May I, and to late Im sure. But some support for those uprights might be good, even just a triangle for each side.

  2. Invest in a real welder man. A 110v welder with flux core wire is a perfect recipe to redo this whole project 10 years later. Previous owner of my 4Runner used a shitty harbor freight welder with the same wire and all the rear bumper welds broke when I backed into a tree. Ended up having to go back and rebuild it with a 220v gas feed welder

  3. This was an awsome build!!! I have the same welder for arouond the houses projects but never thought of utililizing on my truck. Great idea for the weekend !! Watched many of your videos and I have to say you are very methodical and informative… New subscriber here!!!!

  4. put some amber and white led strobes all around the frame 360 degrees, so if you are ever stopped on the side of the road, you will be covered.

  5. Personally I would have added like that diamond wire mesh to the top behind the light to like hold ice chest etc without it scratching up the roof of the truck but I also don’t have a truck or any of the materials to do this so oof

Comments are closed.