49 thoughts on “Installing Our Custom Jet Drive On Our Jet Boat Build!”
Wood blade in jigsaw ?! Lol
Public question as someone who wants to get into welding, why did Wyatt hit the boat with the torch before he started welding?
Ridgeline with the motor in the front and the back slammed all wheel drive?
Aluminum mig tip, always push the puddle, never drag no matter what position. your welds are black and full of contaminents because you're dragging
10/10 have atleast two bilge pumps. Maybe 3.
Is there no end to your talent…
love that jet boat man. you guys are killing it
I wish they went too lz's drift compound
Dude I love this build I'm looking forward to the pay off and putting the whoop ass on ol cleeter hahaha I love his channel too but rivalry and competition is the spice of life👍👍
I think you should wrap the boat in twisted tea.just a thought
Bro it’s aluminum you didn’t need to drill the pilot holes lol either way can’t wait to see this thing rip!
Question………. Are the #BoostedBoiz going to be apart of the Christmas Tree Races this year at the #FreedomFactory? My family and I will be coming this year too watch the races!!!
Who won against the hoonicorn? mr2? Hoonicorn? Can't wait to see hahah
If the intake was further back, you would be able to seal the inside and outside all to the intake. This would allow you to take the pump off without breaking your seal. You will just have to reseal the outside every time you take the pump off, no big deal.
They lost that's why they don't have the video posted yet if he would have beaten hoonicorn it would have been posted already
New truck? Where is that Puerto Rican brap brap brap sidekick at?
What's up with you guys racing the hoonicorn man quit slacking
More jet boat. That boats going to gap old cleetus McFarland
….. you guys racing ken block or what
If you jump that thing and it hits the pump it’s going to break the seal and leak. Not crazy about that. But yet again it isn’t my boat just something I wanted to point out
The welder sounds like a long fart lol
Kyle, I work on yachts, don't use silicone underwater. We only use "sikaflex 295 uv". Usually black below the water line. Black seems to hold up well under water. Clean very well with acetone first and sikaflex the bolt threads too.
Custom parts = custom problems
You had better reinforce that transom on the inside around the pump housing. Weld in or bolt on some angle iron or square tube for strength otherwise that thin transom will flex.
That jet pump looks gnarly on y’all jet boat! Can’t wait to see it finished
Hole in a hull lol
Idk man i guess them pump makers known what they are doing but silicone only to seal? Seems kinda sketch.
Ur living the good life bro…I been watching ur channel awhile now and your , your builds and content had continued to get better… Stay safe N motor on !!!!!!
Jet boat content is what keeps me going. Car guy through and through but I'm hooked on the boats
Run a dry sump for that engine!! That boat will pull allot of gs
haha thats what happens when you don't know what you're doing and you don't read the directions. Fun watching you guys realize boats ain't cars and get it figured out
T love the thaugt….. Make it UUUUUUuuupsss :))))).
You expect silicone to hold up to jumping a jet boat with likely rubber mounts? Maybe I'm missing something but that's like a temporary solution at best and a way to sink at worst
Someone do Kyle a solid and send him a side mirror and some bumper lights for wago asap
Silicone seal both the inside AND outside of the jet housing Kyle, unless you want to really overwork your bilge pump like Jackstand is!
little tip, try a whip and pause motion with the aluminum gun
Wyatt hair cut tho. Lol He looks like he listens to BTS on the weekends.
Dude you are going to smoke ol cleet !! I see the beginning of the jet boat battles. Looks amazing and I'd do it the same way if it were mine.
That thing going to sink. Better get insurance
Honestly, the quality of work being done by them is surprisingly good. Should be a ripper
Why does the welder sound like a dying calf? 😂
Please turbo this boat
Who else saw Wyatt in the background on the swing 😂😂😂
If you go fast enough you won't need to silicone it!
This is rad:) let’s go boiz:) 🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸😊🇺🇸😊😊😊🇺🇸😊🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸 can’t wait for the turbos.
Aluminum Mig Welding Goes "Long wet Fart"
When the race against hoonicorn coming out hopefully the mr² got it
Mig welder is like “can I get a hoooyeahhhh’
A good grinder can fix any bad weld…for your health
Wood blade in jigsaw ?! Lol
Public question as someone who wants to get into welding, why did Wyatt hit the boat with the torch before he started welding?
Ridgeline with the motor in the front and the back slammed all wheel drive?
Aluminum mig tip, always push the puddle, never drag no matter what position. your welds are black and full of contaminents because you're dragging
10/10 have atleast two bilge pumps. Maybe 3.
Is there no end to your talent…
love that jet boat man. you guys are killing it
I wish they went too lz's drift compound
Dude I love this build I'm looking forward to the pay off and putting the whoop ass on ol cleeter hahaha I love his channel too but rivalry and competition is the spice of life👍👍
I think you should wrap the boat in twisted tea.just a thought
Bro it’s aluminum you didn’t need to drill the pilot holes lol either way can’t wait to see this thing rip!
Question……….
Are the #BoostedBoiz going to be apart of the Christmas Tree Races this year at the #FreedomFactory? My family and I will be coming this year too watch the races!!!
Who won against the hoonicorn? mr2? Hoonicorn? Can't wait to see hahah
If the intake was further back, you would be able to seal the inside and outside all to the intake. This would allow you to take the pump off without breaking your seal. You will just have to reseal the outside every time you take the pump off, no big deal.
They lost that's why they don't have the video posted yet if he would have beaten hoonicorn it would have been posted already
New truck? Where is that Puerto Rican brap brap brap sidekick at?
What's up with you guys racing the hoonicorn man quit slacking
More jet boat. That boats going to gap old cleetus McFarland
….. you guys racing ken block or what
If you jump that thing and it hits the pump it’s going to break the seal and leak. Not crazy about that. But yet again it isn’t my boat just something I wanted to point out
The welder sounds like a long fart lol
Kyle, I work on yachts, don't use silicone underwater. We only use "sikaflex 295 uv". Usually black below the water line. Black seems to hold up well under water. Clean very well with acetone first and sikaflex the bolt threads too.
Custom parts = custom problems
You had better reinforce that transom on the inside around the pump housing. Weld in or bolt on some angle iron or square tube for strength otherwise that thin transom will flex.
That jet pump looks gnarly on y’all jet boat! Can’t wait to see it finished
Hole in a hull lol
Idk man i guess them pump makers known what they are doing but silicone only to seal? Seems kinda sketch.
Ur living the good life bro…I been watching ur channel awhile now and your , your builds and content had continued to get better…
Stay safe N motor on !!!!!!
Jet boat content is what keeps me going. Car guy through and through but I'm hooked on the boats
Run a dry sump for that engine!! That boat will pull allot of gs
haha thats what happens when you don't know what you're doing and you don't read the directions. Fun watching you guys realize boats ain't cars and get it figured out
T love the thaugt….. Make it UUUUUUuuupsss :))))).
You expect silicone to hold up to jumping a jet boat with likely rubber mounts? Maybe I'm missing something but that's like a temporary solution at best and a way to sink at worst
Someone do Kyle a solid and send him a side mirror and some bumper lights for wago asap
Silicone seal both the inside AND outside of the jet housing Kyle, unless you want to really overwork your bilge pump like Jackstand is!
little tip, try a whip and pause motion with the aluminum gun
Wyatt hair cut tho. Lol He looks like he listens to BTS on the weekends.
Dude you are going to smoke ol cleet !! I see the beginning of the jet boat battles. Looks amazing and I'd do it the same way if it were mine.
That thing going to sink. Better get insurance
Honestly, the quality of work being done by them is surprisingly good. Should be a ripper
Why does the welder sound like a dying calf? 😂
Please turbo this boat
Who else saw Wyatt in the background on the swing 😂😂😂
If you go fast enough you won't need to silicone it!
This is rad:) let’s go boiz:) 🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸😊🇺🇸😊😊😊🇺🇸😊🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸 can’t wait for the turbos.
Aluminum Mig Welding Goes "Long wet Fart"
When the race against hoonicorn coming out hopefully the mr² got it
Mig welder is like “can I get a hoooyeahhhh’
A good grinder can fix any bad weld…for your health