There was a great deal of positive response to my last Day in the Shop video, here’s a link: https://www.youtube.com/watch?v=-vZf7qx_Q_k
So I decided to make a second installment. Of course things didn’t work out as planned and it ended up being a ‘day and a half’ at the shop instead. It also made it so that it’s turned into a 2 part episode. Don’t worry, both parts will stand on their own if you end up watching them separately.
Also, there’s a Fixing it Forward episode rolled in for good measure. That will be in Part 2.
Here’s a link to (Part 2):
Here’s a link to the extended full version at my website: http://www.ericthecarguy.com/premium-content-web/13-premium-content-videos/1292-a-day-at-the-shop-with-ericthecarguy-2nd-installment-extended-full-version
Camera: Brian Kast
Thanks for watching!
You can donate to Fixing it Forward here: gofundme.com/3a3s27dg
Discussion about this video: http://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/59833-a-day-at-the-shop-with-etcg-2nd-installment-1-2#146433
The best place for answers to your automotive questions: http://www.ericthecarguy.com
Special thanks to Car Part Kings: http://www.carpartkings.com
Tools
Air Compressor: http://www.bendpak.com/TS-5-Elite-Air-Compressor-BendPak.pdf
Brake Lathe: http://www.bendpak.com/wheel-service/brake-lathes/rl-8500.aspx
2 Post Lift: http://www.bendpak.com/car-lifts/two-post-lifts/xpr-10a-lp.aspx
KNIPEX Pliers: http://www.jbtoolsales.com/knipex-8603180-7-pliers-wrench/#oid=1002_1
Delco 1/2″ Impact: http://www.jbtoolsales.com/ac-delco-ari2061b-1-2-drive-compact-impact-driver-kit#oid=1002_1
DeWalt 3/8″ Impact: http://www.jbtoolsales.com/dewalt-dc823ka-3-8-18v-cordless-impact-wrench-kit#oid=1002_1
Welder: http://www.jbtoolsales.com/longevity-migweld-140-140-amp-mig-welder-capable-of-flux-core-and-aluminum-gas-shielded-welding-110v#oid=1002_1
Aluminum Spool Gun: http://www.jbtoolsales.com/longevity-spoolgun-140#oid=1002_1
Beta T-Handles: http://www.jbtoolsales.com/search.php?q=952%2FS7P#oid=1002_1
Power Probe 2: http://www.jbtoolsales.com/power-probe-pp219ft-power-probe-ii-diagnostic-tool-kit#oid=1002_1
1/2″ Torque Wrench: http://www.jbtoolsales.com/gearwrench-85053-micrometer-style-torque-wrench-1-2#oid=1002_1
Mantis pliers: http://www.ipatools.com/products/index.php/ipa-8041.html
Coast Pen Light: http://www.jbtoolsales.com/coast-19648-rechargeable-pen-light/#oid=1002_1
Zep Penetrating oil: http://www.zepautomotive.com/product/Penetrating-Lubricant-Spray
Digital Tire Gauge: http://www.amazon.com/Antetek-Digital-Tire-Pressure-Gauge/dp/B00S0ODBZO/ref=sr_1_125?s=automotive&ie=UTF8&qid=1426784428&sr=1-125&keywords=tire+gauge
Related Videos
Finding Brake Pulsations: https://www.youtube.com/watch?v=AAbET9aKq_g
Disc Brake Replacement: https://www.youtube.com/watch?v=lAviOGXzEUk
Torquing Wheels & Why It’s Important: https://www.youtube.com/watch?v=DA4ug4gHccM
AC System Basics: http://www.youtube.com/watch?v=w17DpGCcRj8
Comebacks: https://www.youtube.com/watch?v=Js2MN0gi4jo
Meet Cameraman Brian: https://www.youtube.com/watch?v=A9TcR3O-98o
Useful articles.
No start problems: http://www.ericthecarguy.com/faq/solving-automotive-no-start-problems
Idle issues: http://www.ericthecarguy.com/faq/solving-automotive-idle-problems
Performance issues: http://www.ericthecarguy.com/faq/solving-automotive-performance-issues
Diagnosing Noises: http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car
Electrical Problems: http://www.ericthecarguy.com/faq/solving-automotive-electrical-problems
Brake Issues: http://www.ericthecarguy.com/faq/solving-brake-problems
HVAC problems: http://www.ericthecarguy.com/faq/solving-automotive-hvac-problems
Leaks: http://www.ericthecarguy.com/faq/finding-and-fixing-leaks
Social Network Links
Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts
Twitter: https://twitter.com/EricTheCarGuy
Google+: https://plus.google.com/100195180196698058780/posts
Instagram: http://instagram.com/ericthecarguy
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
I found a little trick working in a machine shop to convert metric to inches and vice versa and you pull out a calculator and multiply the metric # by .03937 and hit the equal button and there’s your inches and if your converting inches it’s backwards you’d divide instead of multiply.
Eric should be sponsored, maybe Napa could be it?😎
0:49 Barbara's Van is Back!
Hey bud. When you prep aluminum you can't cross contaminate with steel. Your wire wheel may have been the source of your trouble. You. Need and aluminum only wheel that you store in a clean bag or something.
Eric, you have a lot of lights. You could dedicate a video just to you switching all of them on.
Rule of thumb about metallurgy is to only cut .003 at a time so the metal surface isn’t fractured. Is that
your mode with machinist know how?
That was a thermister on the evaporator right? If so what was the third wire for?
Love your videos. But why are you always working on old ass cars man!
hi eric … what about buyng new cars? r u like scotty or have your own opinnion?
rellay weld … hey weld machines providers … get him a machine for welding. ambarressing weld
You make an excellent point of the car being built for the street as a cruiser. I built a car that I initially built to do the same but I went further than initially planned, 12.5 to 1 pistons, heads shaved so my 428cj had about 13.2 to one and the cam I was running really didn't make it a good "street" car, although it was alot of fun, 8mpg, excessive heat, etc. That said my full bodied 67 Fairlane GTA turned 10.34 at 138mph.
Gotta love Eric the Car Guy.
eric, don't use gloves when using a lathe or mill. look it up.
Grinders and paint make me the welder I ain't!
Good to hear fixing it forward will be running in 2020.
Word of advice to anyone when you make a video repair always show a video that you are correctly diagnosing otherwise you're not going to show the video obviously if you are wrong
This Guy Is Not A Mechanic… All This Guy Does Is Install Parts, And All The Cars He Works On Are His Friends And Family, Witch He Does For Free To Make These Videos. Do Not Listen Or Try To Apply Anything He Says On Your Own Car
pushing brake fluid back up into the master cylinder was the begining of all my problems with bad spongy brakes on my 96 chevy pickup!!!!!!
Good bye Eric
That whole cracking the bleeder deal seems like you just begging for issues
That aluminium welding looks sh*t. Are you using the right gas?
Hi, Eric the car guy my wife loves your video you had help her a lot by watching your videos. Well the reason why i'm writing to you cause my wife owns one of the cars you like or favorite. She has a 1993 Acura Vigor 4-door it's her baby she loves Acura. She had taught her self to work on cars she had change break pads with out taking the tire off. I was very proud of her, name is Amber we been together 20 years plus she goes to college at C.W.U Central Washington University. If you can get of hold of her at
Phone number(253) 240-3092
Business websiterover-night.com
hello ericthecarguy how about the cvt fluid for transmission can i use the fluid for not cvt?
Using pliers…
🤣
Aww man…. I know I'm like 4 years late to the party but dude! Gloves and rags on that lathe! I'm a machinist and I am glad theres plenty of people in here giving you grief.. we need you to keep all your fingers and limbs so you can keep on teaching us!
You are doing that right. That's how I have always done it.
Hey Eric do you use All data or Identifix?
These are great 🙂
1 fan lol