Bringing The 1000hp Prelude Back to Life!

43 thoughts on “Bringing The 1000hp Prelude Back to Life!”

1. I want to see that crank when the race season ends. I guarantee its ate up.

2. Wowwwww

3. Can someone get this man some MAXIMAUSA assembly lube?

4. Hi boosted i have a question i have a h22 that wont pop VTEC AT ALL DO U HAVE SOME HELPFUL INFORMATION I NEED HELP

5. I cant believe you guys put a used pump back in this thing rite after doing all that work and almost ruining it from a stock pump. I wouldve fixed the problem and put a better pump on it so you wouldn't have to worry about having this same problem later on. I most definitely wouldnt have put a used stock pump back on it.

6. get that used oil pump out of there!!!

7. just swapped my 00 y7 from auto to manual, now won't start, main relay clicks fast no engine light at all, runs off starting fluid only, replaced and cleaned every ground, any ideas? have two big black wir3w and small blue for it to think it's in park together

8. Instead of doing towels down under the car buy a roll of RamBoard from home depot.

9. I wonder how much metal made it into the top end parts.

10. German shorthairs are great dogs.

11. Well done on the lude running again, so excited too see it again, always make my heart skip a beat, she is a beauty of a car

12. Don’t forget to drop that running-in oil/filter and stick some fresh hi-po stuff in before u send it! ‘Hey Roman, where’s the oil filter’

13. Dont lube the prelude it will nut all over the place

14. Kyle you looked so exhausted at the end of the video.. get some rest brother… we appreciate the daily uploads!

15. GSP'S 4 LIFE!!!!!!!!

16. What about the time you guys built VTEC Vicky?? The engine was in the car when you guys rebuilt her

17. Y’all built vtec Vicky on the lift!!!

18. That upside down crank install was dope ahaha nice guys

19. Rebuilding 1 in the car is called a dirty overhaul

20. Valco Cincinnati 71006 Tube-Grip 2.5" Industrial Size Dispenser https://www.amazon.com/dp/B007IQ4XWK/ref=cm_sw_r_fm_apa_i_wKeGDb2GCR1Q9
    You guys need a couple of these. They work dam good for silicone tubes.

21. Hell yeah !! Glad it worked out..

22. You shud use good oil. Luces oil. Red line or Shafer is the best to Make big power long time abuse

23. Watch you guys all the time thanks for good content!! Just a cool tip I learned from my friend Jamie Davila….I cut off the main shaft of a bad trans and I use that as my alignment tool….makes stabbing the trans like butter forget that plastic tool crap they are not "true"…hope it helps!!

24. It wasnt the same scene for the bearing yall

25. When you put the clutch alignment tool in push up a little bit when you tighten up the clutch bolts next time, it’s helped me in the past.

26. damn shock collars mmm mmm mm also always check them clearances before install just to be safe. then again im coming from subarus soo maybe thats overkill?

27. good thing kyle put the flywheel on, that way you know its not sideways lol XD
    jokes emillio, love ya guys

28. You guys have so much fun it’s awesome to watch.

29. maybe try to pull the wrench instead of pushing it??

30. What a badge on the front ? Can you tell me someone ? sry for bad english. Thanks

31. H

32. Just a little back story before getting to my main point. I am a Navy Vet, currently in the Army, about to retire. My latest MOS is Machinist/welder and a competition sheet metal worker. I have always wanted to use those skills for myself, which I have never been able to do.. Ever since I was 14, I have envisioned a specific custom vehicle; a custom job that I have never seen or heard of. I did end up with the first piece of this vehicles puzzle but it never went any further than a plan; a dream project. My first daily driver was an all original 69 C-10 (307ci, turbo 350, long bed, nothing special). My dream and what I would have loved to see this turned into was a 69 K-10, Crew Cab, Turbo Diesel, pass thru (through) tandem rear axeld 6×6, with late model Bell's &, whistles for suspension and interior. I have had this truck plan blueprinted (hand drawn; not true blueprints LOL) plus I have been planning parts and donor vehicles since I was able to drive but I never found the time or money (mostly, it was a time and a tool/equipment issue) to get it together. Now that I am in my mid 40s and so close to retirement, I will have the time to do what I have been dreaming of. One way or another, I will end up building this truck at some point; tools and equipment would only make it easier and provide a more "presentable" finished product ….. but, even without, I still have plans to complete this build. I can appreciate anyone that helps someone to fulfill a dream; I salute those that help others to reach points where they couldn't have reach on their own. Channels like yours keep my dream alive. I watch the builds that you do and get a renewed excitement about something I have wanted to do for …… 30, 35 years. I thank you for that. Having PTSD/TBI, it often takes having something to look forward to, just to get through some days. Your videos give me that; reenergizing my dream while providing entertainment and making my mind explore new ideas for my plan. Again, I thank you. Keep up the great work. I look forward to your future projects and getting started on my own.

33. New used oil to go with the new used oil pump. wow. send it pappi.

34. Nobody makes billet gears for the pump? That’s the fix for the Miata BP engine, round $200 for a set.

35. Send it!!!

36. waiting for the hatch to comeback to
    Iife 💯💯💯💯💯💯💯❤️❤️❤️❤️❤️❤️❤️👍👍👍👍👍👍👿👿👿👿🤖🤖🤖🤖🙈🙈🙈💀💀💀💀😎😎😎

37. Do we need to start a GoFundMe to get the prelude a nice new bumper with a proper sized hole for the turbo?

38. You guys need to get Kyle to the gym

39. careful with a dog in the shop, dont want any coolant puddles or absorbent pellets on the ground.

40. Like all the videos but damn dude that dude spent a bunch of money to send you fucking oil filters and shit and you can’t even shut out his name again that was the whole reason why He did it I’m sure get with the fucking program bro dam

41. Such a sick save on the h22 woulda been a shame if she popped already.

42. You should get a dog and call her or him "Vtec". My Black Lab, her name is "Shelby" and my wife named her. Seems like a cool dog, better than a little yap yapper.

43. TORQUES LAST ROD BOLT. TOSSES TORQUE WRENCH ON THE GROUND LMAO

Comments are closed.