2001 GMC Sonoma 2.2L Engine Replacement (Part 4) -EricTheCarGuy

Link to full version of the video: http://www.ericthecarguy.com/vmanuals/22-vmanual-store/236-2001-gmc-sonoma-2-2l-engine-replacement-video-full-version

Here’s Part 4 of the 2001 GMC Sonoma 2.2L Engine Replacement video. In this video we switch a few more things over and get the engine ready for install. The new engine block is pretty and we want to make sure it stays that way. We install the timing cover and oil pan as well as the intake and exhaust manifolds. I also cover the operation of the oil pump and name all the sensors on the side of the engine block. If you’re enjoying this series this is a must see for you. Here are some useful links for you.

Link to Part 1 in case you missed it: http://www.youtube.com/watch?v=5ivqj2LjE28&feature=youtu.be

Donate for DIPG: http://www.reflectionsofgrace.org/index.php/diffuse-intrinsic-pontine-glioma-dipg.html

Other videos staring this truck.

Tapered Roller Bearing Video: http://www.youtube.com/watch?v=ccsbu2hT0MI

Lubricating a Chassis: http://www.youtube.com/watch?v=bB2RiRKDQ9k

Serpentine Belt Replacement: http://www.youtube.com/watch?v=Wg1AX77xEBQ

Discussion about this video: https://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/46056-2001-gmc-sonoma-2-2l-engine-replacement-series#65904

Visit me at: http://www.ericthecarguy.com

Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts

Twitter: https://twitter.com/EricTheCarGuy

Google+: https://plus.google.com/100195180196698058780/posts

Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content

Stay Dirty

ETCG

Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

source

Author: avnblogfeed

ANGELHOUSE © 2009 - 2022 | HOSTING BY PHILLYFINEST369 SERVER STATS| & THE IDIOTS ROBOT AND CONTROL INC. |(RSS FEED MODULE)| ALL YOUTUBE VIDEOS IS A REGISTERED TRADEMARK OF GOOGLE INC. THE YOUTUBE CHANNELS AND BLOG FEEDS IS MANAGED BY THERE RIGHTFUL OWNERS (AVNBLOGFEED.COM)

27 thoughts on “2001 GMC Sonoma 2.2L Engine Replacement (Part 4) -EricTheCarGuy

  1. Love this series! Would it have been easier to access the electrical connectors and such on the intake side of the engine by removing the intake manifold while the engine was still in the vehicle, and then installing it after the new engine was back in the truck? Seems like that intake and fuel rail comes off fairly easily.

  2. Eric, what kind of sealer did you use for the water pump? Just black RTV? Or water pump sealer? Thank you for the info, gotta do a leaky water pump this weekend.

  3. When you are putting that front seal on the timing cover, would it be okay to use a piece of wood over top and hit on the wood straight over the seal to knock it in? I don’t see anything wrong with your method I’m just curious if using a solid piece of wood to evenly push in the seal might cause an issue I’m not thinking of.

  4. You can spin oil pump with a 3/8 or 5/16 deepwell socket AFTER you install OP sending unit and on the shaft to prime it.

  5. when you were installing exhaust manifold and reusing old gasket at 30 mins into video that AIR gasket you could of cut two of them out of the new exhaust gasket and created new gaskets for that AIR system i noticed they looked the same 

  6. Question about getting a seal on the oil pan.  You put RTV on the gasket where it touches the oil pan (excepting the dip where the timing cover will go in).  But you do not place RTV on the side of the gasket that touches the block?

  7. eric 2 questions one why not use anti seize on exhaust hardware and why red lock tite on the oil filter stud?

  8. I've got a question; If I was to try to torque a fastener in a recessed area, and I needed to use a three inch extension; Should I compensate for the extension by going up a couple of pounds or go by the book on the torque spec? Example; Replacing an trans mission pan and there  is a heat shield and the catalytic converter in the way; and the fastener is lets say…. 13mm, and it needs to be torqued to 27 ft. lbs.; but I need to use a three inch extension to fasten it; should I up the torque to 29? I'm in a dilemma???? Although the torque manufacturer says not use  an extension…… I'm confused????

Comments are closed.