hand held band saw converted to a bench top model

50 thoughts on “hand held band saw converted to a bench top model”

1. is the trailer finished, the ends here?

2. Where will you use the trailer and is it for working on cars that have been sitting a long time?

3. You might want to take the bandsaw out of the workbench while driving the trailer to prevent it from bouncing around.

4. You just know that felt good.

5. In the trailer, the little welder you were using, did you have coated wire or was the sealing gas used?

6. There's na sh1te wipe like a sna sh1te wipe!

7. Hardcore no welding gloves!

8. Working alone , I find using french cleats the best way to mount cabinets by my self.

9. Is this it for the trailer trash series? If so, too bad. Wanted to see the cabinetry finished and the trailer ready to go.

10. Put it in a vice man

11. Hey there and I like your video I seen doing that new trailer you got all your goodies are ice age toys I also love your Volkswagen

12. With Mr. Mustie there's just no such thing as a one use tool.
    He'll always find a way to make a tool a multi use tool.

13. Let`s see if this welder's wire feed can be fixed – 🙂

14. The morning after a vindaloo for the dog aaaahhhhhhh lol

15. Fairly new subscriber, going through your back catalogue. Great video, but the last 10 seconds were priceless.

16. Great video. I acquired a Greenlee 531over 10 years ago, but never put it to use because the drive chain is broken. I have done an extensive amount of searching for the chain, but have not been successful at finding one.

    I would love to build this adapter if I can find a way to get the saw working. If anyone has any idea where to find parts for these saws, I would sure like to know.
    Bob

17. Super cool. I'm looking for ideas on how to use my everlast welder to make a mount that does just that.

18. 45 degree triangular brace on the tallest upright would add a lot of strength

19. Bwahahaha. Lily at the end…. did she sneak a jalapeno? Apparently, you both have a bit of ingenuity.

20. nice work mr D .?

21. I'd say the band saw fittings are satisfactory and prove to be well built too.. fantastic job mate and you have a great nack with the welder too.. seems your pooch had an irritating itch lol

22. Just wondering, do you own a speed square, framing square, and bubble level?

23. I'm going to try my hand at building that.

24. I'm binging on your videos. Were the double cab and welding trailer finished? I can't find videos and I'm dying to see the finished products! Hope you enjoyed the Death Wish Coffee.

25. AMAZING, LOVE THE VIDEOS.

26. I love what you did on the first tach on the portable band saw table part. It almost looks like you're blowing on it to cool it off really quick so it didn't pull to one side.

27. Hey Mustie, what's the material that the counter top made of?

28. so after a cut short working life in the auto biz @60 y/o im ready to put together my new shop in the house im purchasing. the wife was very cool about my being so fussy with the homes i said no large shed/shop/garages?…not interested..i told her long ago the garage is off limits and for my use only lol…and she knows my love for my hobbies and my building and tinkering. so now i have a waaay oversized garage and a workshop attached with a 2nd floor detached from the main house. im watching your videos to inspire me and get some ideas and i may do what you do alittle… anyway it will be a blast! for me. the only things i need to re buy are the compressor, welders and a floor lift similar to one of yours and im all set…thx for the videos and the inspiration

29. Who goes in the men's room and thinks this stuff would make great shop cabinets?

30. We're coming up on two years now, did you ever put the tool box in the trailer?

31. I may be wrong, but from what I'm seeing, when you were welding on the band saw plate, that was the difference between a gas Mig and a flux core Mig Welder. Am I right? Again, I'm not positive, but I would bet you use a argon/carbon dioxide blend gas on the Miller Mig Welder you use in your shop? I think your allot like me, you just didn't want the fight of rolling out that Miller Welder and the argon tank ..LOL

32. THANK YOU…for sharing.

33. Portaband was made by Porter Cable

34. Hello, is the miller a gas shielded or a flux core welder ?

35. jesus christ that was a long video .but i liked it

36. Now that is what I call an "Ice Wipe". Gotta love the "Puppies".

37. You are talking to us. 😉 Don't stop. I think I speak for thousands.

38. That is one tuff dog…

39. Dog skiing my dogs are world champions 😂

40. Precisioned by hammer,ok.Thumbs up.

41. Great video I need to do the same thing to an old Porter Cable model

42. Did you finish the trailer? I'd love to see the final product. I enjoy your videos.

43. nice

44. I got it. I got it! I got it? I don't got it! ☺️

45. Leave you drivers on some old speaker magnets and they will magnetise – no more dropped screws etc

46. Kipp Handles in place of the jam bolts would make life much easier, no more tightening the bolt with a wrench/socket. I have a problem where wrenches tend to disappear three seconds after they're set on a crowded work bench.

47. One suggestion, fab a plate to cover the bottom of the unit.

48. Very nice setup and no counter space.

49. Hi Mustie
    I have been following the welding trailer series with fervour and waiting with some anguish. When are we going to see #15 an actual road trip and the project in actual use?
    Please do not keep us waiting too long!!!! Keep the great videos coming Thanks.

50. Onde foi parar este trailler-oficina?

Comments are closed.